Mark – I’m setting the Linux state to Invalid based on your comments and will attempt to get this information into the release notes. Since P2e and P3e are capped by their Maximum Bandwidth value to 1Gbps, the other three traffic flows P1e, P4e, and P4i automatically take equal shares and increase their bandwidth to approximately 2. Table lists problems related to the user interface and remote agent. The P1f traffic flow in PG1 is adjusted upwards to 50 percent approximately 5Gbps. Figure Non-DCB, Weight, Maximum Bandwidth, Over-subscription Plot The following paragraphs describe what is happening during each time interval tn shown in Figure The first partition’s traffic flow P1i initially takes its maximum designated approximately 8Gbps of bandwidth when the test application starts to transmit traffic at t0 to that port by itself, not expanding into the remaining unused approximately 2Gbps of bandwidth. The Device Hardware Configuration menu opens see Figure

Uploader: Tygora
Date Added: 20 April 2004
File Size: 20.36 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 40388
Price: Free* [*Free Regsitration Required]

The partition s send flow rate is based on the ratio of that partition s individual weight verses the aggregated weights of all the other actively sending partitions. In the Value column, enter the desired value in the MTU box. P2e continues to take only 1. This required a nc-sedies.

HP Service Pack for ProLiant version Contents

When P4e starts to send at t4, nc-sefies four Ethernet traffic flows take one-fourth of PG0 s bandwidth approximately 1. This value is the percentage of the port s link speed that is the top-end maximum send transmit bandwidth that will be allowed on that specific partition at all times. As I mentioned already there is “no” such nx3fwct. Schauen Sie die Anleitung. I know a number of customers still have ongoing problems with their NC and NC NIC’s and are still experiencing some disconnections, although much less frequently and more minor on the whole.


QLogic 3400 and 8400 Series 10GbE Adapters

When all four partitions or at least the last two partitions are running traffic, they share the space with each other, up to their partition Maximum Bandwidth values and their PG s ETS settings; otherwise, they act as if they are independent connections.

Both Linux and VMware commands control all partitions of both ports simultaneously. That seems to have nc-seties the problem. Setting all of the partition s values to 0 gives every traffic flow on every partition equal access to the port s available bandwidth regardless of which partition they are on, unless they are restricted by the partition’s Maximum Bandwidth settings.

When the third traffic flow P2e starts sending at t2, it only takes its partition s Maximum Bandwidth allowed approximately 1Gbps. When P1i stops sending at t6, the five currently active traffic flows P1e, P2e, P3e, P4e, and P4i will readjust to one-fifth th of the bandwidth approximately 2Gbps eachequally absorbing the bandwidth that has become available.

The remaining approximately 2Gbps of bandwidth is still unused. Click the product type tab: HP Smart Array Par. If disabled, the driver does not wait forauto-negotiation. In non-dcb mode, where the sum of the partition s Relative Bandwidth Weights equals zero i.

If the sum of the relative bandwidth weights is and there is more np one type of traffic flow on a specific partition iscsi and Ethernet, or FCoE and Ethernetthen the combined traffic on that specific partition shares the bandwidth being hc-series to it as if there was nc-seriew one traffic flow on that partition. Click Network and Internet. Overview DA – Worldwide Version 5 2.


The other traffic flows P2e, P3e, P4e, and P4i do not change. Furthermore, each partition s combined traffic flow will be capped by that partition s Maximum Weight setting. Developer’s Guide – Series Ethernet Drivers. Partition P1 s two traffic flows and the traffic flow on partition P2 P2e are still unaffected.

HP Service Pack for ProLiant version Contents – PDF

March Purpose and Contact Information These release notes describe. Again there’s are a couple of advisory’s from HP. On the right pane, click the Configuration tab nnx Figure For more information, visit Text in bold font indicates user interface elements such as a menu items, buttons, check boxes, or column headings. How does this relate to the firmware flashing we have nc-serise made?

One of the 2 nics will randomly lose connection to the switch for about 2 seconds, long enough to trigger that network redundancy was lost.

Device temperature degrees C exceeds maximum allowed.

It is a low-cost, low-power dual port PCIe v2.